Florida Certified EC13004667Veteran-OwnedNo-Commission Electricians

Dedicated Circuit Installation in Jacksonville

Freezers, hot tubs, EV chargers, dryers, ranges, pool pumps, shop tools and home offices all run best on their own circuit. Empire Electric installs dedicated 120- and 240-volt circuits every day for homes across Jacksonville and Northeast Florida, sized to your equipment and installed to code.

Expert Residential Electrical Services in Duval County and Surrounding Areas
Free Written Price

Before any work starts

120 and 240 Volt

15 to 60 amp circuits

Permits Handled

When the job needs one

5-Year Warranty

On our workmanship

What Does Your Appliance Need?

From a garage freezer to a 60-amp EV charger, every circuit is sized to the equipment. Here’s what’s typical.

What Does Your Appliance Need?

Pick what you're adding and tell us a little about the job. You'll see the typical circuit and where the price usually lands.

1. What needs a circuit?

2. Distance from your panel
3. How we get the wire there
4. Room in your panel

Typical setups under the 2020 National Electrical Code, adopted by the Florida Building Code. The equipment's nameplate and installation instructions set the final breaker and wire size, and your electrician confirms it on site.

When an Appliance Needs Its Own Circuit

If any of these sound familiar, a dedicated circuit is usually the fix, and it’s often faster and cheaper than people expect.

A breaker trips when the appliance starts

Lights dim when it cycles on

It runs on an extension cord or power strip

A plug or outlet feels warm

The manual calls for its own circuit

You're adding a new appliance or tool

You're remodeling a kitchen or garage

You're switching from gas to electric

Most Circuits Cost $225 to $1,000

A short 120-volt run beside the panel sits at the low end. A long, high-amperage 240-volt circuit sits at the high end. Here’s what moves the price.

Distance and Route

A circuit next to the panel takes far less wire and time than one across the house, outside or to a detached building.

Amperage

A 20-amp, 120-volt circuit uses small wire and a standard breaker. A 50- or 60-amp, 240-volt circuit needs heavier wire and parts.

Walls and Access

Open attics, garages and crawl spaces are quick. Finished walls, slabs and two-story runs take more care.

Panel Space

Open breaker spaces keep it simple. A full panel may need a tandem breaker, a subpanel or an upgrade.

Outdoor Equipment

Hot tubs, pool pumps and condensers need outdoor-rated disconnects, conduit and GFCI protection.

Permit and Inspection

New circuits usually need a permit in Jacksonville. When yours does, we pull it and schedule the inspection.

Free, written price before we start

We look at the equipment, your panel and the route, then give you a firm price at no charge. You approve it before any work begins, and our work is backed by a five-year workmanship warranty.

Can Your Panel Handle It?

Every new circuit needs a breaker space and enough capacity in your service. Most homes have room for one more. When yours doesn’t, we’ll explain the options and price them before any work starts.

Dedicated Circuits, Start to Finish

For most homes, it’s a same-day job.

01

Tell Us What You're Adding

Request a price online or call. A photo of the appliance’s nameplate and your panel helps.

02

Free Written Price

We size the circuit, plan the route and give you a firm price before any work begins.

03

Permit if Needed

When your circuit needs a permit, we pull it.

04

Install to Code

New breaker, the right wire and the GFCI, AFCI or disconnect the location calls for.

05

Test and Label

We test the circuit under load, label the breaker and clean up.

06

Inspection and Warranty

We meet the inspector when required, and our workmanship is backed for five years.

Learn More About Your Circuit

Garage Freezer Circuits

Does a garage freezer need its own circuit, and does it need GFCI?

Hot Tub Circuits

Breaker size, GFCI and disconnect rules for spas.

Pool Pump Wiring

GFCI, bonding and circuits for pool equipment.

EV Charger Requirements

Breaker, wire and panel checklist for Level 2 charging.

Dedicated Circuit Questions

How much does a dedicated circuit cost in Jacksonville?

Most dedicated circuits we install cost between $225 and $1,000. A short 120-volt circuit near the panel is at the low end, and a long, high-amperage 240-volt circuit for a hot tub, range or EV charger is at the high end. We give you a free, written price before any work starts.

What is a dedicated circuit?

It’s a circuit that runs from its own breaker in your panel to a single appliance or outlet, with nothing else connected. The appliance gets the full capacity of the circuit, so it doesn’t trip or get tripped by other devices.

Which appliances need a dedicated circuit?

Electric ranges, dryers, water heaters, hot tubs, pool pumps, EV chargers, built-in microwaves, dishwashers and disposals, central and mini-split A/C, and large shop tools typically do. The manufacturer’s instructions and nameplate are the final word.

Does a freezer need a dedicated circuit?

Code doesn’t always require one, but it’s a good idea. A freezer on a shared circuit can be shut off when something else trips the breaker, and you may not notice until the food spoils. In a garage, the outlet also needs GFCI protection.

What's the difference between a 15-amp and a 20-amp circuit?

A 20-amp circuit uses heavier 12-gauge wire and can carry more load than a 15-amp circuit on 14-gauge wire. Kitchen, laundry, bathroom and many appliance circuits are 20 amps.

Do I need a permit for a new circuit?

New circuits usually need an electrical permit in Jacksonville and surrounding counties. When yours does, we pull the permit and schedule the inspection, and it’s included in your price.

What if my panel is full?

We may be able to use a tandem breaker if your panel allows it, or add a small subpanel. If your service doesn’t have the capacity for a large load, we’ll do a load calculation and explain your options before you commit.

How long does it take to install a dedicated circuit?

Most dedicated circuits are finished in a few hours, the same day. Long runs, finished walls or outdoor equipment like hot tubs can take longer. We’ll give you the schedule with your price.

Can I install a dedicated circuit myself?

Working inside a panel is dangerous, and new circuits usually need a permit and inspection. A licensed electrician makes sure the breaker, wire and protection match the equipment, which also protects your warranty and insurance.

Need a Dedicated Circuit in Jacksonville?

Tell us what you’re adding. We’ll give you a free, written price before any work starts, and most circuits are done the same day.

(904) 365-7777

service@empireelec.com

Office

5810 Macy Ave, Jacksonville, FL 32211

Hours

Mon–Thu 8:00 am–4:00 pm, Fri 8:00 am–3:00 pm · 24/7 emergency service